WIZM-POT

WIZM-POT

WIZM-POT is an analog rotary potentiometer module featuring an onboard 10kΩ potentiometer (RV09-103E). Powered via 3.3V and GND, it outputs a continuous analog voltage proportional to the rotational position of the knob via its analog output pin (A1), making it ideal for volume control, parameter tuning, sensor threshold adjustment, and user input interfacing.

ADK-Buy Buy now

The WIZM-POT is an analog input module based on a 10kΩ rotary potentiometer (RV09-103E). It functions as an adjustable voltage divider, outputting a smooth analog voltage ranging from 0V up to VCC (3.3V) as the knob is rotated. Dual connector breakout options (standard 2.54mm pitch through-hole header and a 5-pin horizontal keyed JST connector) provide flexible wiring for breadboards, carrier boards, and modular microcontroller platforms like the W55H32L-Application-KIT.


Features

  • 10kΩ Rotary Potentiometer: Onboard RV09-103E component providing linear analog voltage division.

  • Analog Output (A1): Continuously variable DC voltage output (0V to 3.3V) readable by any standard ADC channel.

  • Onboard Filtering: Integrated RC filtering components (R2, R4, C1) to stabilize signal reading and minimize noise.

  • Dual Connection Options: Supports a standard 2.54mm pitch pin header (P1) alongside a horizontal keyed JST connector (J1).

  • Standardized Form Factor: Features four corner mounting holes and a center cutout for modular assembly.


Specifications

Parameter

Value

Model (P/N)

WIZM-POT

Function

Potentiometer 10k

Component / IC

RV09-103E

Interface (I/F)

AD (Analog / ADC)

Revision

1.0

Operating Voltage (VCC)

3.3V DC

Output Type

Analog Voltage (0V – 3.3V)

Connector Pitch

Standard 2.54mm (P1) / Keyed Horizontal (J1)

Pin Count

5 Pins (NC, NC, A1, GND, 3.3V)


Pinout & Hardware Overview

The module provides two parallel pin interfaces: a standard 5-pin 2.54mm pitch breakout (P1) and a 5-pin horizontal keyed connector (J1).

Pin

Type

Description

NC

—

Not Connected

NC

—

Not Connected

A1

Output

Analog voltage output (connect to ADC input pin)

GND

Power

Ground supply reference

3.3V

Power

3.3V DC Power Supply

Top View & Bottom View

topandbottom


Platforms Supported

MicroPython

mpy-logo


Getting Started

Materials Required (excluding potentiometer module)

  • W55H32L-Application-KIT

  • 5-pin female-female JST PH-Style Cable

  • USB Type-C Cable

W55H32L-Application-KIT

Hardware Connection

Connect the WIZM-POT to an ADC-enabled connector (e.g., J3) on the W55MH32L-Application-KIT using the 5-pin JST cable.

Hardware Connection

Then use a USB Type-C cable to connect the WIZ-LINK USB Type-C port on the application kit to your PC.


Sample Code Demo

Software Setup

We will be using Thonny IDE to run the code.

  1. Open Thonny IDE on your PC.

  2. Select the correct COM port for your board.

  3. Set the interpreter to MicroPython (generic).

Refer to the WIZnet documentation page for detailed setup instructions.

MicroPython

from machine import ADC, Pin
import time

# Configure the ADC pin connected to the A1 line of the module.
# Update the pin name to match your carrier board's ADC-capable pin (e.g., 'PA0', 'PB0', etc.)
pot_pin = Pin("PA0")
pot_adc = ADC(pot_pin)

print("Starting WIZM-POT reading...")

while True:
    # Read raw 16-bit unsigned ADC value (0 to 65535)
    raw_value = pot_adc.read_u16()

    # Convert raw value to voltage (assuming 3.3V reference)
    voltage = (raw_value / 65535) * 3.3

    # Calculate percentage (0 - 100%)
    percentage = (raw_value / 65535) * 100

    print(f"Raw: {raw_value:5d} | Voltage: {voltage:.2f}V | Level: {percentage:.1f}%")
    time.sleep(0.1)

wizm-pot Demo