WIZM-433TR3L

WIZM-433TR3L

WIZM-433TR3L is a compact 433MHz wireless RF transceiver module powered by the Ling-TR3L core IC. Featuring a standard UART interface, it allows microcontrollers to easily send and receive serial data over long-range 433MHz ISM radio frequency bands. Dual connection headers (keyed JST-style connector and 2.54mm pitch through-holes) make it ideal for wireless telemetry, remote control, and IoT telemetry links.

ADK-Buy Buy now

The WIZM-433TR3L is a transparent UART-to-433MHz RF data transmission module built around the Ling-TR3L RF chipset. Operating at 3.3V, it converts serial UART communication into 433MHz wireless RF packets, enabling bidirectional half-duplex communication without requiring complex RF stack programming. The module features onboard impedance matching, an IPEX/U.FL connector (RF1) for external 433MHz antennas, an INT status/interrupt pin, and dual connector options for rapid prototyping.


Features

  • 433MHz Wireless Transceiver: Long-range sub-1GHz ISM band RF communication via the onboard Ling-TR3L chipset.

  • Transparent UART Interface: Simple serial TX/RX transmission—plug-and-play without protocol overhead.

  • RF Antenna Flexibility: Onboard IPEX / U.FL coaxial connector (RF1) plus solder pads for spring or whip antennas.

  • Dual Connection Options: Supports a 5-pin standard 2.54mm pitch header (P1) alongside a keyed horizontal lock connector (J1).

  • Standardized Form Factor: Includes corner mounting holes and standard spacing compatible with WIZnet application kits.


Specifications

Parameter

Value

Model

WIZM-433TR3L

Revision

1.0

Core IC / Module

Ling-TR3L

Operating Voltage (VCC)

3.3V DC

Communication Interface

UART (TTL 3.3V)

Operating Frequency

433 MHz (Sub-1GHz ISM band)

Connector Pitch

Standard 2.54mm (P1) / Keyed Horizontal JST (J1)

Pin Count

5 Pins (INT, RX, TX, GND, 3.3V)


Pinout & Hardware Overview

The module provides two parallel pin interfaces: a standard 5-pin 2.54mm pitch breakout (P1) and a 5-pin horizontal keyed connector (J1).

Pin

Type

Description

INT

I/O

Interrupt / Status / Mode pin

RX

Input

UART Data Receive (Connect to MCU TX)

TX

Output

UART Data Transmit (Connect to MCU RX)

GND

Power

Ground supply reference

3.3V

Power

3.3V DC Power Supply

Top View & Bottom View

topandbottom

Platforms Supported

MicroPython

mpy-logo


Getting Started

Materials Required

  • W55MH32L-Application-KIT

  • 5-pin female-to-female JST PH-style cable

  • USB Type-C cable

W55H32L-Application-KIT

Hardware Connection

Connect the WIZM-433TR3L to a UART-enabled connector (e.g., J10 or J5) on the W55MH32L-Application-KIT using the 5-pin JST cable.

Hardware Connection

Then use a USB Type-C cable to connect the WIZ-LINK USB Type-C port on the application kit to your PC.


Sample Code Demo

Software

We will be using Thonny IDE to run the MicroPython script.

  1. Open Thonny IDE on your PC.

  2. Select the COM port corresponding to your board.

  3. Set the interpreter to MicroPython (generic).

Refer to the WIZnet documentation page for detailed initial setup instructions.

MicroPython

from machine import UART, Pin
import time

# Initialize UART
# Note: Adjust UART ID, baudrate, and TX/RX pins according to your specific JST header mapping (e.g., J5 or J10)
uart = UART(3, baudrate=115200, tx=Pin("PB10"), rx=Pin("PB11"))

# Optional status/interrupt pin
int_pin = Pin("PD7", Pin.IN)

print("WIZM-433TR3L Initialized. Ready to send/receive data...")

counter = 0

while True:
    # 1. Transmit periodic test packets over 433MHz
    message = f"Hello 433MHz #{counter}\r\n"
    uart.write(message)
    print("Sent:", message.strip())
    counter += 1

    # 2. Check for incoming RF serial packets
    if uart.any():
        data = uart.read()
        try:
            print("Received:", data.decode("utf-8").strip())
        except UnicodeError:
            print("Received (raw bytes):", data)

    time.sleep(2)

RF Demo